FAQ

Find answers to the most recurring questions based on ADFORS expertise and experience

11 Results

Filters (2) Close filters

How do I apply FibaTape?

FibaTape drywall tapes are self-adhesive fiberglass mesh tapes. As long as the surface is dry and dust free the tape will stick by pressing into place by hand or with a taping knife. The tape is now ready to be coated with joint compound.

Does FibaTape need to be embedded?

Yes. FibaTape has to be embedded in joint compound but not in the same manner as paper tape or FibaFuse tape. FibaTape is self-adhesive and should be pressed into place over the seams or in inside corners before any joint compound is applied. The compound is applied over the tape and because it is a mesh tape the compound actually is forced through the tape. This is one of the reasons for the popularity of FibaTape, the ability to put all the tape in place and then embed.

Can I use Mold-X10 on cement board in my shower?

No. The Mold-X10 fiberglass mesh tape is made for drywall seams and intended to be coated with joint compound. FibaTape’s Cement Board Tape is the product for cement board.  The alkali-resistant coating protects the fiberglass from degradation that can occur with thin-set mortar.

Which tape do I use where cement board meets green board?

The best tape to use if the seam connecting the green board to the cement board is Mold-X10 if the seam is going to be coated with joint compound. This would be done if the seam will not be covered with tile, which means it has to be properly concealed with joint compound so that the area can be painted. If the seam is going to be covered with tile which is most likely the case then use FibaTape’s Cement Board tape. The seam will then be coated with thin-set as the tile is applied.

Can I use FibaTape or FibaFuse on an inside corner?

Yes.  FibaTape can be used to tape inside corners. Just fold it with one hand and press it into the corner with the other. The tape is self-adhesive so it can be applied to all the inside corners before any joint compound is applied. Make sure the tape is tight into the corner without being slightly rounded. If it is rounded then it is not tight into the corner. So when a taping knife is used to apply and smooth the joint compound the taping knife could accidentally cut through the tape. FibaTape does make a special tool for placing the tape into the inside corners.  The dispenser type tool holds a roll of tape and actually rolls the tape tight into the corner and cuts it to the desired length. A must have tool for larger taping jobs.

FibaFuse is pre-creased for corners.  While you can use a taping knife, we suggest using a corner trowel for installation to prevent cutting the tape.

Where are FibaTape and FibaFuse products manufactured?

All our FibaTape and FibaFuse tapes are made in the USA except for Perfect Finish which is made in Canada.

Where can I buy FibaTape?

FibaTape can be found at Home Depot, Lowes, Menards, Sherwin Williams, True Value,  Ace, Do-it-Best and other local hardware stores throughout US and Canada.  All products can also be found online for purchase.  Click here to visit our Where to Buy page.

Does FibaTape meet ASTM Specifications?

Yes. FibaTape products meet the following ASTM standards: D-3775, C-474, D-17777, C-475 and D-3776. Other ASTM standards may be met with our specialty tape products.

Where can I find LEED information on your FibaTape and FibaFuse products?

Sustainability reports exist for both FibaTape and FibaFuse products and are available upon request

How do you install FibaFuse MAX?

Embed the tape in ready-mix joint compound. Once dry, apply a second coat of compound wider than the first. Apply additional coats if needed. Sand with a fine grit sandpaper or sponge. Be sure to apply FibaFuse MAX with the color side down.

Need additional assistance?